diff --git a/radvd.conf b/radvd.conf
deleted file mode 100644
index 159c111..0000000
--- a/radvd.conf
+++ /dev/null
@@ -1,39 +0,0 @@
-interface lo
-{
-	AdvSendAdvert on;
-	MinRtrAdvInterval 3;
-	MaxRtrAdvInterval 10;
-	AdvDefaultPreference low;
-	AdvHomeAgentFlag off;
-	# prefix 2001:db8:1:0::/64
-	# {
-	# 	AdvOnLink on;
-	# 	AdvAutonomous on;
-	# 	AdvRouterAddr off;
-	# };
-	#prefix 0:0:0:1234::/64
-	#{
-	#	AdvOnLink on;
-	#	AdvAutonomous on;
-	#	AdvRouterAddr off;
-	#	Base6to4Interface ppp0;
-	# 	AdvPreferredLifetime 120;
-	# 	AdvValidLifetime 300;
-	# };
-
-	# route 2001:db0:fff::/48
-	# {
-	# 	AdvRoutePreference high;
-	# 	AdvRouteLifetime 3600;
-	# };
-
-        # RDNSS 2001:db8::1 2001:db8::2
-        # {
-        #         AdvRDNSSLifetime 30;
-        # };
-
-        # DNSSL branch.example.com example.com
-        # {
-        #         AdvDNSSLLifetime 30;
-        # };
-};
diff --git a/radvd.conf.bak b/radvd.conf.bak
deleted file mode 100644
index 73781da..0000000
--- a/radvd.conf.bak
+++ /dev/null
@@ -1,86 +0,0 @@
-interface lo
-{
-	AdvSendAdvert on;
-# This may be needed on some interfaces which are not active when
-# radvd starts, but become available later on; see man page for details.
-	# IgnoreIfMissing on;
-
-# These settings cause advertisements to be sent every 3-10 seconds.  This
-# range is good for 6to4 with a dynamic IPv4 address, but can be greatly
-# increased when not using 6to4 prefixes.
-	MinRtrAdvInterval 3;
-	MaxRtrAdvInterval 10;
-
-# You can use AdvDefaultPreference setting to advertise the preference of
-# the router for the purposes of default router determination.
-# NOTE: This feature is still being specified and is not widely supported!
-	AdvDefaultPreference low;
-
-# Disable Mobile IPv6 support
-	AdvHomeAgentFlag off;
-
-# example of a standard prefix
-	# prefix 2001:db8:1:0::/64
-	# {
-	# 	AdvOnLink on;
-	# 	AdvAutonomous on;
-	# 	AdvRouterAddr off;
-	# };
-
-# example of a 6to4 prefix
-#
-# Note that the first 48 bits are specified here as zeros.  These will be
-# replaced with the appropriate 6to4 address when radvd starts or is
-# reconfigured. Be sure that the SLA ID (1234 in this case) is specified
-# here!
-	#prefix 0:0:0:1234::/64
-	#{
-	#	AdvOnLink on;
-	#	AdvAutonomous on;
-	#	AdvRouterAddr off;
-# This setting causes radvd to replace the first 48 bits of the prefix
-# with the 6to4 address generated from the specified interface.  For example,
-# if the address of ppp0 is 192.0.2.25 when radvd configures itself, this
-# prefix will be advertised as 2002:C000:0219:1234::/64.
-#
-# If ppp0 is not available at configuration time, this prefix will not be
-# advertised, but other prefixes listed in the configuration will be
-# advertised as usual.
-#
-# When using the Base6to4Interface option, make sure radvd receives a
-# SIGHUP every time the ppp0 interface goes up, down, or is assigned a
-# new IPv4 address.  The SIGHUP will cause radvd to recognize that the
-# ppp0 interface has changed and will adjust the advertisements
-# accordingly.
-	#	Base6to4Interface ppp0;
-# If the IP address of ppp0 is assigned dynamically, be sure to set the
-# lifetimes for this prefix to be small.  Otherwise, hosts on your network
-# may continue to use a prefix that no longer corresponds to the address
-# on ppp0!
-	# 	AdvPreferredLifetime 120;
-	# 	AdvValidLifetime 300;
-	# };
-
-# example of a more specific route
-# NOTE: This feature is not very widely supported! You may also need to
-# enable it manually (e.g. on Linux, change the value of
-# sysctl accept_ra_rt_info_max_plen to 48 or 64)
-	# route 2001:db0:fff::/48
-	# {
-	# 	AdvRoutePreference high;
-	# 	AdvRouteLifetime 3600;
-	# };
-
-# RDNSS
-# NOTE: This feature is not very widely implemented.
-        # RDNSS 2001:db8::1 2001:db8::2
-        # {
-        #         AdvRDNSSLifetime 30;
-        # };
-
-# DNS Search Lists
-        DNSSL branch.example.com example.com
-        {
-                AdvDNSSLLifetime 30;
-        };
-};